Can anyone comment on RSP redundancy with SSO mode?
- Hw-module Slot R0 Reloaded
- Hw-module Slot R0 Reloading
- Hw-module Slot R0 Reloadable
- Hw-module Slot R0 Reloader
Cheat Tables for yuzu. Contribute to zarroboogs/yuzu-ct development by creating an account on GitHub. Hw Module Slot R1 Reload Entertainment Limited, hereinafter called (bgo.com or the Company). Read our full review. Visit casino -70.-Prize pool: 300% up to €2000. Eg:%CMRP-3-CHASSISMONITORONLINETIMEEXCEEDED: R0/0: cmand: Reloading slot because it has failed to come online Conditions: The module that's failing to boot may have been newly inserted and may have not been upgraded to ROMMON version 16.2(1r) to be consistent with other cards in the router chassis. This older ROMMON will not be. To reset a specific node, or to put a node into maintenance mode, use the hw-module location command in System Admin EXEC mode. The force keyword forces an immediate reload or shutdown of the router without waiting for an orderly system shutdown. Symptom: The log as below is appeared when the ISR4300 of version 16.9.2 and 16.10.1 reloaded although there is no slot 2 on ISR4300%CMRP-3-PFUINITIALIZATION: R0/0: cmand: The RP has failed to initialize a Power Supply/Fan module controller because the idprom is empty for slot 2 the same log also found on ISR4400 of version 16.9.2 and 16.10.1 no matter whether there is Power module on slot 2.
I have a test 7507 with rsp-k4pv-mz.120-32.S8.bin on both RSP2s. I've done
this:
service single-slot-reload-enable
redundancy
no keepalive-enable
mode sso
And it doesn't seem to ever sync the slave
ranttest#show red
Redundant System Information :
------------------------------
Available system uptime = 14 minutes, 49 seconds
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = hsa
Maintenance Mode = Disabled
Communications = Down Reason: Simplex mode
Current Processor Information :
-------------------------------
Active Location = slot 2
Current Software state = ACTIVE Uptime in current state = 13 minutes, 24 seconds
Image Version = Cisco Internetwork Operating System
Software
IOS (tm) RSP Software (RSP-K4PV-M), Version 12.0(32)S8, RELEASE SOFTWARE
(fc1)
Technical Support: http://www.cisco.com/techsupport
Hw-module Slot R0 Reloaded
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Mon 20-Aug-07 16:34 by leccese
BOOT =
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer (slot: 3) information is not available because it is in 'DISABLED'
state
Hw-module Slot R0 Reloading
ranttest#redundancy force-switchoverCannot perform switchover until the standby is fully initialized.
The box is up, its got two OSPF adjacencies, maybe a hundred routes - its
not doing anything fancy, so I'm kind of stuck here. The production target
is 7507s /w RSP4s, the same OSPF, and about 180k routes via BGP. Any idea
Hw-module Slot R0 Reloadable
what might be wrong here?
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
Hw-module Slot R0 Reloader
archive at http://puck.nether.net/pipermail/cisco-nsp/